ST6000 /ET6000全新人機取代GP4000



PFXGP4601TMD – Pro-face可程式人機介面GP4000系列

  • -

PFXGP4601TMD – Pro-face可程式人機介面GP4000系列

PFXGP4601TMD – Pro-face可程式人機介面GP4000系列

GP-4601T
機型: PFXGP4601TMD

Specification of PFXGP4601TMD

TFT Color LCD   (65,536 色) /   顯示解析度: SVGA

功能規格

顯示類型 TFT 彩色 LCD
顯示大小 12.1″
解析度 800 x 600 畫素 (SVGA)
有效可視面積 W246.0 x H184.5 mm [W9.69 x H7.26 in.]
顯示顏色 65,536 色(無閃爍)∕16,384 色(閃爍)
背光 White LED (User nonreplaceable parts. When replacement is required, contact your local distributor.
亮度控制 16 階 (使用觸控面板調整)
背光使用年限 50,000 hrs. or more (continuous operation at 25°C [77 °F] before backlight brightness decreases to 50%)
語言字型 Japanese: 6,962 (JIS Standards 1 & 2) (including 607 non-kanji characters) ANK: 158 (Korean fonts, Simplified Chinese and Traditional Chinese fonts are downloadable.)
字元大小 標準字型:8 x 8、8 x 16、16 x 16 及 32 x 32 點字型,筆劃字形:6 至 127 點字型,影像字型:8 至 72 點字型
字型大小 標準字型:寬度可達 8 倍;高度可達 8 倍。
文字 8 x 8 點 100 字 x 75 列
8 x 16 點 100 字 x 37 列
16 x 16 點 50 字 x 37 列
32 x 32 點 25 字 x 18 列
控制記憶體 可變區 SRAM 64 KB (Replaceable Lithium battery for backup memory)
程式區 FLASH EPROM 132 KB (Equivalent to 15,000 steps)
應用程式記憶體 FLASH EPROM 32 MB (including a logic program area)
資料備份 SRAM 512K byte (資料備份用) *512KB=HMI 320KB+控制192KB(可替換式鋰電池供記憶體備份時使用)
時鐘精確度 每月 ±65 秒(室溫及電源關閉時會造成偏差)
觸控面板類型 Resistive Film (matrix)
觸控面板解析度 40 x 30 keys/screen
觸控面板使用年限 1,000,000 times or more
介面 序列埠 (COM1) RS-232C Asynchronous Transmission Data Length: 7 or 8 bit, Parity: none, Odd or Even, Stop Bit: 1 or 2 bit, Data Transmission Speed: 2,400 bps to 115.2 kbps, Connector: D-Sub9 (plug)
序列埠 (COM2) RS-422/485 Asynchronous Transmission Data Length: 7 or 8 bit Parity: none, Odd or Even Stop Bit: 1 or 2 bit Data Transmission Speed: 2,400 bps to 115.2 kbps, 187.5kbps (MPI) Connector: D-Sub9 (plug)
乙太網路 (LAN) IEEE802.3i/IEEE802.3u,10BASE-T/100BASE-TX,接頭:模組化插孔 (RJ-45) x 1
USB (TYPE-A) 符合 USB2.0 (TYPE-A) x 1、電源電壓:DC 5 V ±5 %、輸出電流:500 mA 或以下、通信距離:5 公尺或以下
USB (mini-B) Conforms to USB2.0 (mini-B) x 1 Communication Distance: 5 m or less
SD 卡 SD Card Slot x 1
  1. 其它字型大小可使用 Editor 軟體進行設定
  2. Up to 60,000 steps can be converted in software. However, this reduces application memory capacity (for screen data) by 1 MB.
  3. 視作業溫度及裝置機齡而定,時鐘每月偏差可達 -380 至 +90 秒。若此偏差程度對系統造成問題,則用戶應進行監視並在必要時加以調整。

一般規格

國際安全標準

 bv ccc  ce classnk ctick dnv eac  gl kc  abs rina ul508 ul508ansi

輸入電壓 DC 24 V
額定電壓 DC 19.2 至 28.8 V
允許的壓降 10 ms 或以上
消耗功率 未供電給 USB 裝置時。 12 W or less
背光關閉(待機模式) 7 W or less
背光變暗(亮度:20 %) 8 W or less
湧入電流 30 A 或以下
耐壓特性 AC 1,500 V 20 mA 1 分鐘(充電部端子與 FG 端子間)
絕緣電阻 DC 500 V,10 MΩ 或以上(充電部端子與 FG 端子間)
周圍空氣溫度 0 to 55 °C [32 to 131 °F]
儲存溫度 -20 to 60 °C [-4 to 140 °F]
環境濕度 10 to 90 % RH (Wet bulb temperature: 39 °C [102.2 °F] or less – no condensation.)
儲存濕度 10 to 90 % RH (Wet bulb temperature: 39 °C [102.2 °F] or less – no condensation.)
灰塵 0.1 mg/m³ (10-7 oz/ft³) or less (non-conductive levels)
汙染程度 適用於汙染程度 2 的環境
環境規格 非腐蝕性氣體的環境
耐氣壓震動(高度範圍) 800 至 1,114 hPa(海拔 2,000 公尺或以下)
耐震動 IEC/EN61131-2 compliant, 5 to 9 Hz Single amplitude 3.5 mm [0.14 in.], 9 to 150 Hz Fixed acceleration: 9.8 m/s², X, Y, Z directions for 10 cycles (approx. 100 min)
耐衝擊 符合 IEC/EN61131-2 規格,147 m/s²,X、Y、Z 方向 3 次
耐雜訊 Noise Voltage: 1,000 Vp-p, Pulse Duration: 1 µs, Rise Time: 1 ns (via noise simulator)
抗靜電放電力 接觸放電法:6 kV(IEC/EN61000-4-2 第3級)
接地 Functional grounding: Grounding resistance of 100Ω, 2mm² (AWG 14) or thicker wire, or your country’s applicable standard. (Same for FG and SG terminals)
結構規格 IP65f NEMA #250 TYPE 4X/13(裝入外殼時在前面板上)
冷卻方法 自然氣流
大約重量 2.5 kg [5.5 lb] 或以下(僅限顯示裝置)
外部尺寸 W315x H241x D56 mm [W12.4 x H9.49 x D2.2 in.]
挖孔尺寸 W301.5 x H227.5 mm [W11.87 x H8.96 in.], Panel thickness area: 1.6 to 5 mm [0.06 to 0.2 in.]
  1. The front face of the GP unit, installed in a solid panel, has been tested using conditions equivalent to the standards shown in the specification. Even though the GP unit’s level of resistance is equivalent to these standards, oils that should have no effect on the GP can possibly harm the unit. This can occur in areas where either vaporized oils are present, or where low viscosity cutting oils are allowed to adhere to the unit for long periods of time. If the GP’s front face protection sheet becomes peeled off, these conditions can lead to the ingress of oil into the GP and separate protection measures are suggested. Also, if non-approved oils are present, it may cause deformation or corrosion of the front panel’s plastic cover. Therefore, prior to installing the GP unit, be sure to confirm the type of conditions that will be present in the GP’s operating environment. If the installation gasket is used for a long period of time, or if the unit and its gasket are removed from the panel, the original level of the protection cannot be guaranteed. To maintain the original protection level, be sure to replace the installation gasket regularly.
  2. 在尺寸公差方面, +1/-0 mm [+0.04/-0 in.] 以及 R 角皆小於 R3 [R0.12 in.]。

外部尺寸

 

 

開孔尺寸

 

 

包含接線的外部尺寸

 


即時詢價

加入line好友id:@dml9854r
加入凱虹企業LINE@
ID : @dml9854r